Thursday, January 8, 2015

:: The New Paper-flooring-Pt.2 DIY


*affiliate links enclosed
** I was CAUGHT @ MRL!  Photobucket

By now you’ve already seen my kitchen floor. Especially if you follow my Instagram
#paperflooring



I’ve done the process before in our ONLY Bathroom, about 3 years ago. You can click that link to see how I did it the last time—OVER VINYL. The space, in my kitchen, is about 6 times the area—so we exhausted most of our materials. The technique is pretty much the same. I’m going to show what I did different this time and how it worked out for me.




1. Find a Chump-Enlist a Helper OR willing participant… ;)

2.Measure paper for strips-- 




rather than tear the paper or cut with scissors; this time I cut it with a chop saw! My roll was 35 inches wide, so I cut it every 7 inches allowing for 1/2 inch over lap on each side. Making Roughly 6 inch planks. I marked the paper first at 7 inch intervals, taped it with Frog tape, measured and marked again.

The tapeFrogTape 1358465 Multi-Surface Painting Tape, Green, 1.41-Inch Wide by 60 Yards Long
 was put there to keep the paper from tearing when we cut it. The CHUMP Helper… taught me that! Ssshhh…! don’t tell him I said that. ;)


3. Cut paper with a chop saw—on the tape with measurements. Nice and easy—don’t hurry. 



We had very little fray. Turned out pretty nice! FIVE- 7 inch rolls, ready to go! We used


** Please use caution with saw. Follow the manufacturer’s instructions. Wear protective gear. Eye and Ear protection, etc. Notice I edited my photos… lets assume we follow our own advice, okay?

4. Prepare your floor.

 

I Vacuumed, swept, Vacuumed again… damp mop to remove any dust. I had to use Vinegar and good old fashioned elbow grease, around the stove to remove the oil.


5. I used Elmer’s Wood Glue, why Wood glue and not All PURPOSE? The bottom line AGAIN! COST! This time we used a roller and rolled it onto the floor and onto the back of the paper and of course after putting the paper down, we rolled it with glue to seal. That’s 1-2-3 applications of glue. Be thorough. Oh, I also used a 1:1 ration of glue thinned with water; and mixed in a bucket (equal parts)

 

**NOTE: This picture was right after we started and shows glue on the 3rd application—after the paper was down—something was amiss. I had to stop—scrape the floor and give it an extra scrubbing—and we also had to thin the glue a little more. It was too thick. 


Chump rolling glue!


Me, hard at work laying out the paper strips. 

I implied before that there would be an over lap. There was and it was about 1/2 inch on both sides. REALLY, I EYE-BALLED IT. The floor covered really well. The paper was thin enough to allow some of the imperfections to come through the paper—and it helped to give the appearance of real wood. 


Because the temps were so nice of GLUING DAY- I took it slow and easy, and well, time got away from me, I could have probably done the entire floor but instead I only did half on Saturday and the other half on Sunday. 

BUT FIRST! THIS HAPPENED. …Saturday afternoon Momma dog, that lives in or around the old abandoned house nextdoor, came over and dropped off some things, while grabbing a snack on the front porch. She is a ‘scardy-dog’ and won’t stick around. But she left these little pups. (there are NOW 7 a week later) 


…BACK TO THE FLOOR- Sunday.

6. Create Faux Wood Characteristics: Realizing my miscalculation of time and weather—as soon as it was dried I got busy and creative with ‘wood look details’

 

I did NOT get any pictures of this technique, except after—but it’s basically a 3 inch roller between my fingers and I would brush the paint on – and DRAG it where I wanted the black paint. You can see a tutorial on this method here. In this condition, it looks like something you’d see at SIX FLAGS in the Old West part of the park! I also used the Scratch Repair Markers to make lines and create some knot holes. I really just went wild with it! That part was fun. What was even more fun, was seeing the Honey’s face when I started this process. He truly thought I was messing up all the hard paper work.


7. Stain- I brushed it on and left the stain on it— and let it dry! I took pictures of the stain on the floor BEFORE POLY… but they all look alike. I know this is stain only not poly—because of the socks. 




** another NOTE: If I do this again—I will try a stain and poly combination/mixRather that 2 separate applications and dry times. MINWAX makes some, if you’ve tried let me know how it worked for you, if you liked it, etc.

Ok-

8.  Polyurethane Application—BRUSH ON!  2 COATS are needed for a good seal. ...but by this point, it had gotten really REALLY cold, the pilots were blown out on the cook stove, no FIRE could be built in the wood stove, the fans were blowing and the kitchen window (on the NORTH side of the house) was opened up. I even unplugged the fridge so the compressor wouldn’t kick and ignite the flames due to fumes. 

Honey wanted to roll it, but it made bubbles in the poly. Thankfully, it was just a small area, and it was where the fridge sits. I let it dry while I started on the rest of the
room. It took 24 hours to dry—it doesn’t in normal temperatures; check the weather
for warm days.  ** When warm days come apply second coat. ;) 


… and make sure you have proper ventilation.

Ups and Downs-- 

UPs::
  • Cutting the paper with the saw went way faster was easier on the hands/ arthritis.
  • Rolling the Glue, rather than brushing each piece and the floor twice, was also a time saver and a KNEE SAVER. 
  • ENLISTING A SECOND PERSON—PRICELESS!

DOWNS::
  • TIMING: NOT USING TIME WISELY- work, work, work until it’s done, you never know when Weather or puppies might T-bone the schedule and create delays. 
  • TIMING:  PLAN TO HAVE no visitors and the kids go to Gramma’s or at school, etc-- (it helped that we did NOT HAVE OUR LITTLES the last week in December) 
  • TIMING:  BE REALISTIC-  I planned on it taking 5 days; thinking it would really only take 3 1/2... IT took 5. (Saturday- Wednesday) 
** my downs are HUMAN ERROR. Not really having anything to do with the project
directly. 

If you’re still reading this far! WOW! and THANK YOU!
If you’ve done something similar—let me know, so I can visit your blog and read about your technique and experience.
If you have questions, feel free to contact me via email or leave a comment I’d be more
than happy to answer any questions if I can. 






New Flooring pt 1

Bathroom: Faux Wood Floor on vinyl

Paper-flooring Update

I'm sharing this post here:
Catch as Catch Can @ MRL 
‘Til next time, Be Blessed~

      Patricia



*~*~*~*~*~*~*~*~*~*~*~*~*~*~*~*~*~*~*~*~*~*~*~*~*~*~*~*~*~
Do not grow weary in well doing for in due season you will reap if you faint not.”  Galatians 6:9

14 comments:

Kathy Felsted Usher said...

How long will the flooring last? What cleaning method do you use?

A Daughter of the King said...

This is wonderful! I am especially impressed with the faux painting. You are so brave! I've used the poly stain on kitchen cabinet shelves and on my desk. both have lasted for years and it was super easy. I don't know about durability on the floor, though.

Audrey said...

What a job but it looks really good. Love how you aged it.
Blessings,
Audrey Z.

Gail Wilson said...

I just read pt 1 and pt 2
Kudos to you!
cutting paper with the chop the saw? brilliant!

I love how you enhanced the paper with the stain and markers.

great job Patricia (and chump) :) I need one of those! lol

gail

Shug said...

I am amazed with the outcome. I have never heard of this before...but I find it very interesting!! I have a lot of traffic in and out of my house....does it last or do you later experience walking trails?
Neat idea!!

Kris said...

It looks fabulous!!! Wow!! Impressed!
xo Kris

Carol OurSearsKitHome said...

Pat,
Wowee! So amazing.

Linda @ Itsy Bits And Pieces said...

Quite an adventure, Pat! Fun to read...it looks beautiful!

Betsy@My Salvaged Treasures said...

Wow, what an amazing technique! Love it!

Janie Girl said...

I just started following you. What an awesome walk through! Thanks for posting :)

Dr. Who said...

Did your paper get bubbles anytime during the process? I'm just wondering which is better to use, Elmer's glue or wood glue? What was your ratio of water to glue?(Your floors turned out gorgeous!!!)

Miksmissus said...

just for durability answers, if you get poly for floors, and not cabinets, it dries in 5 hours even in cold weather...i dont know about freezing though....and you can use poly on stairs that get a lot of traffic and you'll still have years of value

the bubbles do happen, i use pva glue (aussie)...just trust yourself

Bildi said...

Hi, would you know if it works on tiles as well? and can i still mop the floors after? Thank you!

Anonymous said...

First of all, this is the scripture that I have on my email. I enjoyed yours and thought you would enjoy this one.
"Give thanks in all circumstances, for this is God's will for you in Christ Jesus."
I Thessalonians 5:18
I absolutely love what you have done. Great instructions too. Thanks for posting this. I am thinking of trying. Blessings